• Cures in minutes by sunlight or UV lamp
• Resists scratches & yellowing
• Non-toxic, BPA & VOC-free formula
• Ideal for resin casting & crafting

TotalBoat Colored UV Cure Resin is available in 3 unique kits of colored UV Cure Resin. They are high-gloss, fast-curing craft resin that’s fun and easy to use - just fill your resin molds then expose to natural or artificial UV light. Cures fast and hard in just a few minutes. Perfect for small resin castings to make unique DIY resin jewelry pendants, rings, bracelets, necklaces, figurines, keychains and more. Formula is non-yellowing and scratch resistant. Blend colors to create custom shades of Colored UV Cure Resin.

PRIMARY APPLICATIONS: Castings and coatings

THINNING: Do not thin or add any solvents to TotalBoat UV Cure Resin.

CLEANUP: Use denatured alcohol or isopropyl alcohol before the resin has cured. Once cured, it must be mechanically removed.

MOLD RELEASE AGENTS: Use an appropriate aerosol mold release agent such as Smooth-On Ease Release 200 or Universal Release Agent, or a mold release wax such as Collinite Mold Release Paste Wax. For best results, when applying a paste-type mold release wax, apply and polish out 4-5 coats of wax prior to using Colored UV Cure Resin.

COLORANTS/TINTS: Mica Powders, alcohol tints, pigment dispersions, universal pigments. DO NOT use water-based tints - always perform a test to ensure it achieves the desired results.

Surface Preparation

Molds, Mold Release Agents, Substrates:

An appropriate mold release agent is recommended for casting applications, though it is not required. A mold release agent will help the cured casting release from the mold easily, while preserving the surface of the mold, extending the useful life of the mold. The casting will take on the exact impression and texture of the mold. For a high-gloss finish, a mold release wax can be applied and buffed out to get the smoothest surface. Applying 4-5 coats of mold release wax will ensure the easiest demolding process and consistent finish. Aerosol mold release agents are also available. Use Smooth-On Ease Release 200 for a matte finish, or Smooth-On Universal mold release spray for a high-gloss finish.

Wood and Porous Substrates:

When casting Colored UV Cure Resin with a porous material such as wood, it is imperative to seal or stabilize the porous material to prevent bubbles from coming out of the porous material. Ensure that the wood's moisture content is less than 12% and seal the surface with a seal coat of UV Cure Clear Resin or a clear epoxy product prior to using it for any castings.

Application

Exothermic Reaction:

The cure of TotalBoat Colored UV Cure Resin is an exothermic reaction and will generate heat when the specified bandwidth of light comes in contact with the resin. The amount of heat generated is proportional to the mass of resin that is being cured, as well as the intensity of light.

Blending:

Blend or swirl different colors of the Colored UV Cure Resin kit together to form unique color patterns.

Adding Tints, Pigments, and Colorants:

Tints and colorants can be added to Colored UV Cure Resin to create custom colors, as well as unique special effects. Alcohol ink pigments, mica powders, pigment dispersions and other non-water-based tints can be used. It is imperative to mix in the tints in a mixing cup very quickly and pour into the desired mold before the resin starts to set up, taking extra care to stay out of sunlight. Always perform a test sample casting with any colorants before attempting to use them in the final project, to ensure that it achieves the desired results. Adding more pigments or tints to Colored UV Resin may require substantially more UV light exposure to cure.

Dispensing:

Only dispense the amount of Colored UV Cure Resin being used. Pour slowly and as close to the desired location to avoid cascading, which may induce air bubbles. A heat gun can be used to remove any bubbles before introducing UV light to the resin for curing. Wave the heat gun a few inches away for a few seconds - the bubbles should rise to the surface. Do not overheat the material, as it can permanently burn or distort the surface of the resin.

Curing:

TotalBoat Colored UV Cure Resin does not require the addition of any other materials to cure. When Colored UV Cure Resin is exposed to UV light (365-395nm) the resin will react and start to cure. Some light sources in this bandwidth include black lights and sunlight. Avoid any unnecessary light exposure, if possible, to prevent premature curing or shortened working time. The cure time of Colored UV Cure Resin is dependent on the intensity of UV light and the mass of the material. The light source may need to be moved around a mold or from different angles to ensure a complete cure. The resin will heat up as it is reacting with light and will cool if the light source has been removed, or when it has completely cured. If the material still feels soft or flexible once demolded, it is not fully cured. Continue exposing the material to UV light until it has become very firm and hard.

Demolding

The demold time of Colored UV Cure Resin is dependent on the amount of UV exposure, the mass of the casting, and the thickness of the casting. This is usually between 5 and 25 minutes. If a casting comes out of the mold and feels soft on the side that was in contact with the mold, expose that surface to light for 1-2 minutes until it is fully cured.

Product Storage

Storage Conditions: Store Colored UV Cure Resin in a cool, dark, dry place, below 65°F. Always replace the cap IMMEDIATELY after dispensing and close the cap tightly. Always store Colored UV Cure Resin in the original bottle it comes in.

Application Data

Physical Data