Jocelyn Teixeira
- Total activity 482
- Last activity
- Member since
- Following 0 users
- Followed by 0 users
- Votes 1
- Subscriptions 76
Articles
Recent activity by Jocelyn Teixeira-
How should TotalBoat Lust Rapid Recoat Marine Spar Varnish be applied with a spray gun?
For most spray applications, reduce TotalBoat Lust Marine Spar Varnish by 10-25% or more, as needed, with TotalBoat Spray Thinner 101. Always use the minimum amount of spray thinner necessary to ac...
-
What is the correct way to apply TotalBoat Halcyon Water-Based Marine Varnish with a spray gun?
For spray applications, TotalBoat Halcyon Water-Based Marine Varnish can be thinned with water up to 20%. Most spray applications only require a 5 to 10% reduction, and some spray guns may not requ...
-
Can you buff TotalBoat Halcyon Water-Based Marine Varnish?
TotalBoat Halcyon Water-Based Marine Varnish can be buffed. Allow the varnish to dry for at least 5 to 7 days, then wet sand with 400-grit, 600-grit, and 1000-grit sandpaper. Polish with TotalBoat ...
-
Can naphtha be used to thin TotalBoat Wet Edge Topside Paint?
Naphtha formulated for use with paint may work, but the results can't be guaranteed. It is recommended to use TotalBoat Brushing Thinner 100 to thin TotalBoat Wet Edge Topside Paint. { "@context...
-
How should TotalBoat Halcyon Water-Based Marine Varnish Gloss be prepared before applying TotalBoat Halcyon Water-Based Marine Varnish Satin?
Sanding is not required between coats of TotalBoat Halcyon Water-Based Marine Varnish if it is overcoated within 48 hours.However, when transitioning to satin, it is best to allow the varnish to cu...
-
How should TotalBoat Lust Rapid Recoat Marine Spar Varnish Gloss be prepared before applying TotalBoat Lust Rapid Recoat Marine Spar Varnish Matte?
Sanding is not required between coats if TotalBoat Lust Rapid Recoat Marine Spar Varnish is overcoated within 48 hours.However, when transitioning to matte, it is best to allow the varnish to cure ...
-
How should TotalBoat Gleam Marine Spar Varnish Gloss be prepared before applying TotalBoat Gleam Marine Spar Varnish Satin?
Sanding is not required between coats of TotalBoat Gleam Marine Spar Varnish if it is overcoated within 48 hours.However, when transitioning to satin, it is best to allow the varnish to cure for 48...
-
Can TotalBoat ThickSet Cast + Coat Deep Pour Epoxy be used as a seal coat?
Yes, TotalBoat ThickSet Cast + Coat Deep Pour Epoxy can be used as a seal coat. { "@context": "https://schema.org", "@type": "FAQPage", "mainEntity": [ { "@type": "Question", ...
-
What kind of mold release can you use with TotalBoat 2-Part Polyurethane Marine Flotation Foam?
A wide variety of materials can act as mold release agents for TotalBoat 2-Part Polyurethane Marine Flotation Foam.Products ranging from dedicated mold release agents to various marine or automotiv...
-
What is the full cure time for TotalBoat TotalTread Non-Skid Marine Deck Paint?
When properly applied under normal conditions, TotalBoat TotalTread Non-Skid Marine Deck Paint should become tack-free in as little as 3 hours and be ready for use within 24 to 48 hours. The minimu...